{"id":12385,"date":"2026-11-22T15:00:00","date_gmt":"2026-11-22T07:00:00","guid":{"rendered":"https:\/\/www.sprintpcbgroup.com\/?p=12385"},"modified":"2026-11-16T11:58:19","modified_gmt":"2026-11-16T03:58:19","slug":"hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return","status":"publish","type":"post","link":"https:\/\/www.sprintpcbgroup.com\/ko\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/","title":{"rendered":"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards"},"content":{"rendered":"<div data-elementor-type=\"wp-post\" data-elementor-id=\"12385\" class=\"elementor elementor-12385\" data-elementor-post-type=\"post\">\n\t\t\t\t<div class=\"elementor-element elementor-element-426c6971 e-flex e-con-boxed e-con e-parent\" data-id=\"426c6971\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t\t<div class=\"e-con-inner\">\n\t\t\t\t<div class=\"elementor-element elementor-element-18860dd4 elementor-widget elementor-widget-text-editor\" data-id=\"18860dd4\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<p>On a Hydraulic Control System PCB, most valve jitter, drift and false trips trace back to the board rather than the control algorithm. High coil current, PWM switching and weak sampling signals share one piece of material, so ground return paths, copper thickness uniformity, stackup and via quality decide how clean the current loop can be. Choose a multilayer or heavy copper PCB supplier by its evidence on inner-layer copper uniformity, lamination and via reliability, and separate the power path from the sampling path physically before tuning the loop.<\/p><h2>Why the Board, Not the Algorithm, Limits Valve Current Control<\/h2><p>Many people think the core of a hydraulic control board is closed-loop tuning: stabilize the proportional valve current and you are done. After all these years, I feel the real headache is not in the algorithm but in how to keep a board from tripping over itself between large currents and tiny sampling signals. A Hydraulic Control System PCB sounds quite routine, but once proportional-valve or servo-valve drive is involved, the current loop, the ground return and the sampling traces are all crowded onto the same material, and any small physical non-uniformity ends up as noise in the current loop.<\/p><p>I once ran into an injection molding machine project where the valve spool jittered slightly on site. The control engineer&#8217;s first reaction was to change the closed-loop gain, and an afternoon of tuning had no effect. When we opened the board, only a single row of vias had been left between the power ground and the sampling ground. When the large current passed, the ground level was lifted by a few millivolts and the sampling reference had already drifted. However fast the closed-loop algorithm, the current it sampled was itself dirty, and no amount of tuning helped. It was later solved not by changing code but by redrawing the stackup and having a reliable multilayer pcb manufacturer make new prototypes, isolating the power loop from the signal loop between layers. Once the ground plane was complete, the jitter went away.<\/p><p>This episode made me very picky about choosing a multilayer board supplier. A multilayer pcb supplier is not good enough just because it can laminate a few layers. The dielectric thickness between layers, copper foil uniformity and warpage after lamination all affect the impedance and thermal distribution of large-current traces. On a hydraulic control board the coil drive current is often not small, so the traces need to be wide and the copper thick, but thick copper brings reduced etching accuracy and local overheating. So the process capability of a heavy copper pcb manufacturer is critical: if the copper thickness is uneven, the resistance distribution is inconsistent, the voltage drop in the current sampling section drifts with temperature, and the closed-loop zero drifts with it.<\/p><p>My habit now is that before doing the hydraulic drive section, I first confirm whether the heavy copper pcb supplier can give stable copper thickness tolerance and reliable inner-layer connections. Some factories claim to be able to make thick copper, but the actual connection strength between the inner layers and the vias is insufficient; after a few thermal cycles micro-cracks appear, and when the current is large the board heats up. Nothing can be seen on the board surface, but the current loop begins to jump sporadically. This kind of problem is torturous to investigate because it does not occur every time, and it is easy to blame the sensor or the solenoid valve, while the root lies in the manufacturing quality of the board.<\/p><p>Hydraulic systems demand high real-time performance from the control. Once the closed loop is disturbed by ground bounce, thermal drift and uneven copper thickness, the spool position is affected and eventually shows up as pressure fluctuation or sluggish action. I think the approach for this kind of board has to be reversed: first make sure the power path and the sampling path are physically clean, and then talk about closed-loop response. Many field faults are not a failure of the control strategy; the underlying electrical path simply never gave the closed loop a reliable working environment.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-25b97cf5 elementor-widget elementor-widget-image\" data-id=\"25b97cf5\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"image.default\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<img fetchpriority=\"high\" decoding=\"async\" width=\"600\" height=\"400\" src=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-products-1.webp\" class=\"attachment-large size-large wp-image-12347\" alt=\"hydraulic control system pcb products-1\" srcset=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-products-1.webp 600w, https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-products-1-18x12.webp 18w\" sizes=\"(max-width: 600px) 100vw, 600px\" \/>\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-18eb212e elementor-widget elementor-widget-text-editor\" data-id=\"18eb212e\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<h2>Ground Planes, Stackup and Heavy Copper in Practice<\/h2><p>In my years of working on hydraulic drive control, my biggest feeling is that the board itself is underestimated by too many people. When people talk about proportional valves, they always start with PID parameters, control frequency and response speed, but once on site, the source of many repeatedly untraceable jitters and drifts is actually buried in the layout and stackup of the <a href=\"https:\/\/www.sprintpcbgroup.com\/ko\/pcb-applications\/industrial-control-automation-pcb\/\">Hydraulic Control System PCB<\/a>. This board is different from an ordinary industrial control board: the power loop and the signal loop are crowded on the same substrate, and a slight carelessness in the return path is amplified by the coil into a very concrete fault.<\/p><p>I once stumbled on a closed-circuit hydraulic station. The valve spool kept jittering slightly under low-frequency dither, the current feedback was covered with dense glitches, and we tuned on site for a whole afternoon; later, when the temperature in the cabinet rose, the overcurrent protection even tripped falsely now and then. When we opened it up, there was nothing much wrong with the board design itself, but the ground plane had been chopped into pieces by vias and traces, and the power ground and signal ground were mixed together. When I redrew the board, I kept the ground plane intact and made a single-point join only near the power entry. After that I truly realized that if the stackup advice from a multilayer pcb manufacturer follows only the habits of ordinary digital circuits, the board made may be unsuitable for driving a strongly inductive load like a coil.\u00a0<\/p><p>In the years I have worked with hydraulic control boards, my biggest feeling is that many people put their energy in the wrong place from the start. People like to stare at control algorithm parameters, as if tuning the closed loop well settles everything, when in fact the physical structure of the board has already fixed the performance boundary. Especially for the part carrying large current, if the copper thickness of the Hydraulic Control System PCB is insufficient or the stackup is unreasonable, no amount of software can compensate for it afterward.<\/p><p>The year before last I reworked the control board of a small hydraulic station. The original board used a conventional multilayer process; the circuit driving the solenoid valve carried continuous large current, and after some time of use the copper foil became noticeably hot and the spool response got slower and slower. Later we switched to a manufacturer that makes Heavy copper PCB, re-proofed the board, changed the drive loop to thick copper layers and relaid the ground plane; with the same program, the valve action became much snappier. This experience made me realize that a Heavy copper PCB supplier and a multilayer pcb manufacturer are not something you can pick at random: their process capabilities differ a lot.<\/p><p>The role of multilayer boards in hydraulic control is also easily underestimated. The difference between a four-layer and a six-layer board is not only routing density; complete ground and power planes strongly affect the current return path. Especially when PWM signals and analog signals coexist, the stackup arrangement directly decides whether interference crosses over. I have seen a four-layer board where, because the middle layer was split improperly, the PWM edge noise coupled directly into the sensor interface, causing the oil pressure reading to jitter when the load changed. After it was revised into a six-layer board, with the analog signals placed between two ground planes, the situation stabilized.<\/p><p>On the matter of driving a solenoid valve with PWM, many people think the higher the frequency the better, but that is not so. Whether the current waveform is good has to do with the parasitic inductance on the board, the freewheeling loop area and the copper foil resistance. I once saw very obvious ringing on a sample board, where the spike at the switching node almost used up the voltage margin of the driver chip. After I re-split the power ground and signal ground and placed the freewheeling diode as close to the coil terminal as possible, the spike came down. This shows that isolation and partitioning at the layout level are more effective than piling on more capacitors.<\/p><p><span style=\"font-family: inherit; font-size: inherit; font-style: inherit; font-variant-ligatures: inherit; font-variant-caps: inherit; font-weight: inherit;\">I have made quite a few hydraulic valve control boards and gradually formed a not very mainstream view: people spend too much time choosing switching transistors while overlooking that the PCB itself is where the current actually has to travel. The reliability of a Hydraulic Control System PCB is seventy percent in the layout and thirty percent in the components. Coil current is not a small signal; several amperes to a dozen amperes run back and forth on the board, and if the copper foil is slightly thinner or there are slightly more vias, heat builds up there, and over time the board either burns or the parameters drift.<\/span><\/p><p>Early on I used a linear approach to drive a small proportional valve. The coil current was not large, but all the heat was in the pass transistor, and the heatsink occupied half the board. Later I switched to PWM; the surface temperature of the switching transistor came down, but the board began to reset occasionally. After a round of investigation I found it was not a chip problem at all: at the instant of turn-off, the coil&#8217;s back-EMF punched a spike between the power plane and the ground plane that happened to cross a feedback trace I had not handled well. This lesson made me understand that PWM is not simply a matter of using the switching transistor as a switch; the discharge path on the board must be reserved in advance, and you cannot expect a single TVS to solve everything.<\/p><p>So when I communicate with a multilayer pcb manufacturer now, the first thing I do is not ask about the number of layers but about inner-layer copper thickness and via current capability. Many factories have no problem making multilayer boards, but when it comes to inner-layer thick copper above 3 oz, the uniformity after lamination is hard to predict. I once had an ordinary multilayer pcb supplier make a six-layer board with outer layers nominally 2 oz and inner layers 1 oz; half a year later the vias on the large-current loop developed micro-cracks, and when we opened it up the copper foil was pitifully thin.\u00a0<\/p><p>In the years I have worked with hydraulic control systems, I increasingly feel that spike suppression is thought of too simply by many people. The protection logic inside a chip is certainly convenient, but once on the board, the problem almost always lies in how the freewheeling loop is routed. The energy released at the instant the proportional-valve coil turns off on a Hydraulic Control System PCB is not small; if the freewheeling diode is a bit far from the connector and the loop area is slightly larger, the spike shoots up immediately. This really cannot be solved by adding one or two clamp devices. The reference ground of the clamp device must land on the same low-impedance plane as the ground of the power switch; otherwise the clamp voltage floats and the switch will still overvoltage.<\/p><p>Later I switched to a multilayer board factory that specializes in power boards, and things improved. Many a multilayer pcb manufacturer is fast but does not understand power loops and just arranges layers by the logic of an ordinary digital board. A suitable multilayer pcb supplier will confirm with you which nets carry large current and how the second-layer ground plane should be kept intact. Thick copper is not marketing talk here either: the copper foil voltage drop during large-current switching is very real, and it directly affects the actual effect of the clamp loop. So afterward I regularly used a Heavy copper PCB supplier for boards with outer layers of 2 oz or more, with some boards even requiring 3 oz. But thick copper is not a cure-all: a Heavy copper PCB manufacturer can thicken the copper, but you still have to control the loop area yourself. My habit is to put the freewheeling and clamp on the same side, keeping the path of current from the coil through the freewheeling device back to the coil as short as possible, and not letting the return cross the whole board. Ramp control can ease a tight layout somewhat: slowing down the duty-cycle change lowers the spike amplitude, but the response gets mushy. When debugging, I generally check the physical position of the freewheeling loop first, then change the clamp parameters, and only last tune the ramp.<\/p><p>In the years I have worked on hydraulic control boards, I increasingly feel that everyone&#8217;s attention is in the wrong place. When the current loop is unstable, many people&#8217;s first reaction is to swap in a better op-amp, a higher-resolution ADC, or even change the software filtering algorithm. But if the board&#8217;s own problems are not solved, all those actions are in vain. Once PWM starts, instantaneous currents of several amperes are pumped back and forth on the ground line, and the ground bounce near the sampling point can completely drown the signal. Look with an oscilloscope: the waveform across the sampling resistor is not a clean ramp at all, but has a pile of glitches riding on it. If the sampling window is off by just two or three microseconds, the current value read can differ by several tens of milliamperes. Rather than doing all kinds of fancy compensation in software, it is better to first physically separate the power ground and signal ground on the board, and then place the sampling filter capacitor tight against the ADC pin.<\/p><p>I have also paid tuition on the power traces. Although the steady-state current of a hydraulic valve coil is not large, perhaps around one ampere, the peak current at switching instants can reach several times the steady state. At first I used an ordinary 1 oz copper board; after running for a while, touching the back of the board by hand, the power loop area was very hot and the edges of the copper began to discolor. Later I found a manufacturer that specializes in heavy copper to re-proof the board and made the power section 4 oz, and the temperature rise dropped immediately. However, heavy copper boards are not without trouble: trace width and spacing cannot be made too fine, and if the process is not well controlled during multilayer lamination, layer alignment will go wrong. Many a multilayer pcb manufacturer claims it can make eight or ten layers, but if you ask whether they often do mixed heavy copper lamination, the answer becomes vague.<\/p><p>When dealing with suppliers I now ask very directly. When looking for a multilayer pcb supplier, I open by asking how many ounces their heavy copper process can reach, what range the etch factor is controlled to, and whether they have a habit of producing copper-thickness cross-section reports. Some suppliers quote very low, but the line-width deviation of the etched heavy copper layer is outrageously large, and after assembly the PWM switching characteristics of every board are different, which makes debugging miserable. A Heavy copper PCB supplier and an ordinary multilayer board supplier look like the same group of manufacturers, but their internal process capabilities differ greatly. Later I settled on one manufacturer; although the unit price is a bit higher, every batch of boards comes with measured copper thickness and dielectric thickness data, saving a great deal of time going back and forth arguing. A hydraulic control board working long-term in a vibration environment may, if the bond between copper foil and base material is insufficient, develop hidden delamination after a year or so, and this kind of problem is the hardest to trace.<\/p><p>I have stepped deep into the pit of sampling timing. Books all say that PWM center-aligned sampling gives you the average current, and I did as they said, but the ripple never came down. Only after capturing the waveform did I find that the ringing after the power transistor turns off lingers until near the midpoint of the cycle, especially when the load inductance is large and the ringing decays slowly. If you sample at the point where the ringing is strongest, the value you read is biased, and the direction of the bias differs each time. Later I moved the sampling point to a position a short delay after PWM turn-on, waiting until the ringing had completely died out before sampling, and the current loop became much more stable. The parasitic inductance of the traces on a Hydraulic Control System PCB changes the duration and frequency of the ringing, so when you change to another board this delay may have to be retuned; there is no one-trick solution.<\/p><p>I also struggled for a while over the choice of PWM frequency. If the frequency is too high, switching loss is large, and however well a heavy copper board can cope, it cannot withstand long-term heating. If the frequency is too low, the current ripple is large and the valve spool shows visible jitter. I tried lowering it from a dozen kilohertz, and when it dropped to eight or nine kilohertz the spool began to be restless. In the end I compromised on a middle value, and together with the inductance of the coil itself, the ripple could be kept within an acceptable range. My experience is that you should not believe a supplier who slaps his chest and says the higher the frequency the better; you have to look at the load characteristics and the parasitic parameters of the board yourself. What can really build a stable current loop on a hydraulic control board is often not pushing one part to the extreme but tuning the cooperation between PWM, sampling, layout and copper thickness. Finding a reliable Heavy copper PCB manufacturer is only the first step; the debugging work that follows is where the real time goes.<\/p><h2>Current Sampling, Back-EMF and Supplier Evidence<\/h2><p>After making several hydraulic valve control boards, my view of current sampling differs from what much of the literature says. That material always revolves around PWM switching edges and ADC trigger phase, as if once the sampling point is placed accurately the current loop will be rock steady. But in practice I would rather put my energy into the board itself, especially the layout and manufacturing of the Hydraulic Control System PCB. Because noise, offset and drift in the sampling chain are, nine times out of ten, not something software can rescue; the physical structure of the board decides how clean a value you can actually sample.<\/p><p>The most memorable case was the same current sampling circuit where, after switching to another <a href=\"https:\/\/www.sprintpcbgroup.com\/ko\/pcb-manufacturing\/multilayer-pcb\/\">multilayer pcb manufacturer<\/a>, the amplitude of the sampling jitter dropped by a whole order of magnitude. Not a line of software was changed and the hardware schematic was untouched; purely because the stackup and ground plane were handled differently, the effect was worlds apart. That was when I realized that concepts such as synchronous sampling and center alignment have very limited meaning in the face of a poor ground return path. Whether the sampled value is biased often depends on where your analog ground and power ground meet, and whether the sampling trace passes by the switching node.<\/p><p>Another point: many people like to add a low-pass filter after current sampling to filter out the glitches brought by back-EMF, thinking it will make the closed loop more stable. I tried this route but found that once the filter is added too aggressively, the current loop becomes sluggish, especially when the spool moves quickly, and simply cannot keep up. Back-EMF comes fast and goes fast; if you try to suppress it with software or a conventional RC filter, you drag down the normal control signal as well. I prefer to separate the drive loop and the sampling loop at the hardware level, so that the interference produced by back-EMF never enters the sampling channel, instead of filtering it after it has come in.<\/p><p>On the large-current part, I have also stepped into pits. Early on I thought the thick-copper boards recommended by a Heavy copper PCB supplier would solve heating and voltage drop, but later I found that if the inner-layer copper thickness of a multilayer board is uneven, or the vias are not specially treated, thick copper can actually worsen interlayer bonding. There was one batch of boards where the copper thickness looked sufficient on the surface, but after working for a while local heating appeared near the sampling resistor and the current reading began to drift slowly upward. The investigation found that the inner-layer copper thickness was substandard and the via resistance was high, so the actual potential of the sampling reference point was not the design value. So when I look for a Heavy copper PCB manufacturer now, I do not look only at their nominal finished copper thickness; I care more about the uniformity of the inner-layer copper and the via reliability test data.<\/p><p>When choosing a multilayer pcb supplier, many peers like to compare price and delivery time, but I care more about whether they have made similar hydraulic control or motor drive boards. This type of board has a characteristic: the same board carries both large-current drive nets and very sensitive analog sampling nets. A factory without experience easily goes wrong on the stackup arrangement, for example placing the sampling trace between two high-frequency switching layers, or splitting the analog ground plane into pieces. These problems will not make the board stop working completely, but they leave your current sampling values always carrying a layer of indescribable jitter that software compensation can never clean up.<\/p><p>In the end, on the matter of current sampling, I think you cannot look only at the little circuit in front of the ADC. PWM-synchronous sampling is of course useful, but it is only the last step. If there are problems in the earlier links of layout, stackup, ground return and the supplier&#8217;s manufacturing stability, however accurately the sampling phase is set, what you sample is still a pile of garbage data. So in projects I usually put more than sixty percent of my effort into the physical implementation of the PCB design rather than agonizing over the few microseconds around the sampling point. Only when the board is done right do those theoretical synchronization, filtering and disturbance suppression measures have room to work.<\/p><h2>Current Loop Problems, Port Detection and Multilayer Stackup<\/h2><p>After so many years on hydraulic control system PCBs, my biggest feeling is that many people think the problems of the current loop are too complicated. They keep mentioning feedforward, back-EMF compensation and model-based regulators, wanting to embed the whole stochastic dynamic into the controller, but in actual projects I have seen far too many boards with current loop faults whose causes turned out to be very primitive: traces too thin, copper thickness uneven, connector contact resistance too high. If these basic problems are not solved, the fanciest algorithm is in vain. Especially many engineers who now make Hydraulic Control System PCB lack reverence for the underlying physical path of the current loop; once the coil causes inductance change or back-EMF interference, the current sampling immediately drifts. Is that a software problem or a hardware problem? I think eighty percent of the time the hardware margin was not enough.<\/p><p>Let me also talk about port state detection. I have seen many designs use a voltage divider with a current-limiting resistor to judge the coil connection state: when the port is disconnected it reads high, and when the coil is connected it reads low. The logic looks fine, but in actual use the false alarm rate is not low. A coil rarely goes completely open; more often it suffers inter-turn short circuits or local thermal damage, in which case the port level hardly changes, and the controller still believes the coil is online and keeps outputting the current it should, finally burning the power transistor or the coil even worse. In other cases, a connector develops micro-interruptions of a few tens of milliseconds due to vibration, the port level jumps back and forth, and the controller frequently reports faults and recovers by itself, so field maintenance personnel do not know whether to trust the alarm. So I think judging coil health purely by the high or low port level is too crude.<\/p><p>My own habit is that when the current loop has problems, I first look at the copper thickness and traces of the PCB. The continuous current of many hydraulic valve coils is not small and the transient current is even larger, and ordinary 1 oz or 2 oz copper simply cannot take it, especially when the power ground return path is interrupted, and the current sampling point shows an obvious voltage collapse. I generally look for a reliable Heavy copper PCB supplier, and I look not only at how many ounces they nominally can make but at the inner-layer copper uniformity and the thickness tolerance after lamination. I used a supplier before whose nominal 4 oz measured only a little over 3 oz in places, and as a result the voltage drop of the coil drive loop was inconsistent and the response speeds of two valves were clearly different; it took a long time to trace it to the board itself. Later I switched to a manufacturer that specializes as a Heavy copper PCB manufacturer, made the copper 5 oz and ran a uniformity test, and the same problem never appeared again. Heavy copper boards have another advantage: fast heat spreading, which is especially friendly to the area near the coil driver transistors, but you also have to pay attention to the quality of lamination and drilling, otherwise via fracture problems become more prominent.<\/p><p>The choice of multilayer boards is equally critical. A Hydraulic Control System PCB is rarely a double-layer board, because the analog current sampling, digital control signals and power ground need to be separated; generally at least four to six layers, and eight for more complex ones. Many people think any multilayer pcb manufacturer can make the same board, but the differences are considerable. I once had an eight-layer board whose inner power plane was split too finely, so the coil return path wandered a long way, the ground-bounce noise of the current sampling became noticeably larger, and the control loop could not be stabilized however it was tuned. Later I switched to another multilayer pcb supplier, redid the stackup design, strictly separated power ground and signal ground, and laid a complete reference plane under the drive loop, and the current noise dropped immediately. This made me understand that when people say the current loop bandwidth is insufficient, sometimes it is not a bandwidth problem at all, but the board&#8217;s return path design is unreasonable and interference mixes straight into the sampling signal.<\/p><p>As for port detection, I now prefer to use current waveform characteristics to assist the judgment rather than looking only at the port level. For example, when the coil is normal the current rise rate is within a certain range; if there is an inter-turn short, the equivalent inductance drops and the current rises faster; if connector contact is poor, high-frequency glitches appear on the current waveform. These characteristics can be seen through ordinary sampling, and it only takes the processor to reserve a bit of computing power for simple waveform judgment, which is far more reliable than a simple threshold level. Of course, this is not a cure-all either: the biggest difficulty of port state detection lies in distinguishing an open load from an internal controller fault. For example, when a power transistor breaks down the port level may also be abnormal, and if the software logic is written too simply it is easily misjudged as coil damage.<\/p><p>When all is said and done, people who work on hydraulic control systems should not always think of compensating everything in software.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-564a454b elementor-widget elementor-widget-image\" data-id=\"564a454b\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"image.default\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<img decoding=\"async\" width=\"600\" height=\"400\" src=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-products-2.webp\" class=\"attachment-large size-large wp-image-12348\" alt=\"hydraulic control system pcb products-2\" srcset=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-products-2.webp 600w, https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-products-2-18x12.webp 18w\" sizes=\"(max-width: 600px) 100vw, 600px\" \/>\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-7cd5859f elementor-widget elementor-widget-text-editor\" data-id=\"7cd5859f\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<h2>Dither Frequency, Layout and Heavy Copper Uniformity<\/h2><p>Recently I was tuning the control board of a hydraulic proportional valve and found that people have somewhat mythologized dither. It seems that as long as a small AC signal is superimposed on the current loop, the spool will obey and hysteresis will disappear. But running it on a Hydraulic Control System PCB is not like that at all. As for the frequency parameter, many people open with 70 Hz as the starting point, as if anything below 70 does not deserve to be called dither. My own experience is that 70 is indeed fairly stable for some pilot stages, but for a power-stage spool it often takes a larger amplitude to cooperate, otherwise the signal goes in and simply cannot move the spool, which amounts to superimposing it for nothing.<\/p><p>The problem is not the software configuration but the board itself. A Hydraulic Control System PCB usually handles PWM power output and weak sampling signals at the same time; if the ground plane is cut up in a mess, the dither signal crosses from the power return path into the feedback channel, and what the sampling side sees is a mass of glitches. Then however you tune the frequency, it is like racing the noise. Later I gave the board to a multilayer pcb manufacturer to re-proof, changing the stackup from four layers to six, running power ground and signal ground separately and then joining them at a single point, and the effect was immediate. So when I look for a multilayer pcb supplier now, I do not ask about price first; I first ask for the lamination structure and impedance control report, which is more substantial than anything else.<\/p><p>Another easily overlooked item is copper thickness. If the large-current branch still uses 1 oz copper, the voltage drop of the dither signal on the PCB trace cannot be ignored, especially as the frequency rises and the skin effect increases the equivalent resistance, so the waveform actually reaching the coil is already distorted. A <a href=\"https:\/\/www.sprintpcbgroup.com\/ko\/pcb-manufacturing\/thick-copper-pcb\/\">Heavy copper PCB supplier<\/a> will generally recommend 2 oz or thicker, but the level of Heavy copper PCB manufacturer varies quite a lot. Some factories do not control side etching well when making thick copper boards, the actual line width becomes narrower, local heating is severe, and instead the dither amplitude becomes unstable. I have encountered the same Gerber made by two factories, where on the oscilloscope the current waveform of one was clean and the other blurry, and the difference was in the uniformity of the copper foil.<\/p><p>So I am not very hung up on the so-called typical frequency window now. What dither frequency to set has to go back to the mechanical response of the spool itself and be tested. Some people use the textbook cutoff frequency to cap the upper limit; I think that is only a reference, not a dead line. When actually commissioning a machine, I sweep upward from a low frequency, find the point where hysteresis begins to shrink noticeably, and then decide the final value together with temperature rise and noise. 70 Hz can be used, but it is not suitable for all valves. Once the hardware foundation is laid, with the board done well, enough copper thickness and a reasonable stackup, dither can truly be effective. Entering a number in software is very simple; what is really difficult is making that number become a perceptible micro-vibration on the spool without introducing new trouble.<\/p><p>In these years of tuning hydraulic proportional valves, I have found that everyone&#8217;s attention on dither goes entirely to waveform generation, and hardly anyone cares about the layout of the Hydraulic Control System PCB itself. Once, on site, the spool always jittered near a certain opening. With a current probe on the oscilloscope, both the PWM ripple and the dither envelope looked quite clean, yet the valve simply would not settle. Later, when we dissected the board, we saw that the feedback trace ran half a circle around the power area from the sampling resistor to the op-amp, and the PWM switching spikes crossed directly into the virtual ground of the current loop. This taught me a principle: dither cannot be superimposed cleanly by algorithm alone; the ground bounce and coupling on the board are the hidden killers.<\/p><p>I have also stepped into pits when looking for a multilayer pcb supplier. Many factories only ask for the layer count and copper thickness and do not ask how you handle the analog ground and power ground of the current loop. My earliest batch of boards was made by an ordinary multilayer board factory, who treated the entire inner layer as one solid ground, and as a result the current sampling of the multi-channel valves interfered with each other and the dither waveform was covered with a pile of glitches. Later I switched to a multilayer pcb manufacturer experienced in industrial control power supplies, which built the current sampling loop separately on an inner layer and bridged it to the power ground at a single point, and the glitches came down. This difference does not show in the datasheet at all; it can only be felt by trial in batch debugging.<\/p><p>On heavy copper boards, I was at first very superstitious about the parameters given by a Heavy copper PCB supplier, thinking the thicker the copper the steadier the current. But with one batch of valve drivers using 4 oz inner layers made by a Heavy copper PCB manufacturer, at a PWM frequency of only 8k, I found the dither amplitude differed by nearly 15% between channels. The investigation later showed it was not a design problem but poor copper thickness uniformity, which made the thermal gradient near the sampling resistor inconsistent, and the temperature drift moved the zero of the current feedback. So when I talk to a Heavy copper PCB supplier now, I ask about copper thickness tolerance and hot-press uniformity first, and current-carrying capacity afterward.<\/p><p>On the current loop, I do not quite agree with seeing dither simply as occupying dynamic range. If you treat the dither amplitude as a test signal, it can tell you whether the phase margin of the current loop is really enough. For example, for a proportional valve rated at 4 A with 200 mA of dither superimposed, the instantaneous current peak may reach 4.5 A. Many boards look fine when designed with a 120% range, but when the phase margin is insufficient the current loop overshoots near the dither frequency, and clipped feedback waveforms are only the later result; the root lies in loop compensation. So when tuning a board now, I first let the dither run and then see whether the current loop step response shows ringing.<\/p><p>As for the frequency relationship between PWM and dither, I do not agonize over whether it is an integer multiple. A high PWM frequency can indeed make the current ripple smaller, but the parasitic capacitance on a multilayer board couples high-frequency ripple from the power ground to the feedback end, and instead makes the dither waveform unclean. My own approach is to put PWM at around 12k and superimpose the dither independently at low frequency, keeping the two without a fixed beat frequency, while ensuring the bandwidth of the sampling loop is low enough to block the high-frequency components. That way, even if they are not integer multiples, the mechanical filtering of the spool can suppress the envelope fluctuation.<\/p><h2><span style=\"font-family: inherit; font-size: inherit; font-style: inherit; font-variant-ligatures: inherit; font-variant-caps: inherit; font-weight: inherit;\">Temperature Compensation and Thermal Paths<\/span><\/h2><p>The longer I work on the Hydraulic Control System PCB, the more I feel that temperature compensation is thought of too complicatedly by many people. I have seen quite a few peers write a pile of lookup tables and compensation logic in firmware, trying to correct system drift with one on-board temperature sensor, but the results were not good. The problem is not that the algorithm is not refined enough, but that the board&#8217;s own physical characteristics were not stabilized. If the power section and signal section of a board are crowded together and the copper is not thick enough, then however you compensate in software, once the temperature changes a little, the reference voltage, the ADC reading and the drive characteristics of the servo valve coil each drift in different directions.<\/p><p>My understanding of temperature is rather direct: the board has at least two completely different thermal paths. One is that the reference source and op-amps on the circuit board are affected by local temperature rise; its time constant is relatively short, and a thicker board with more copper pour can hold it down. The other is the coil inside the valve, which has its own thermal resistance, and with the large thermal mass of the valve block its temperature changes much more slowly. With time constants so different, expecting one temperature sampling point to describe both at once is something I think simply cannot be done. Especially after the coil heats up its resistance rises, and the same PWM output produces less actual current, so the valve response becomes soft. This problem cannot be solved by an on-board NTC; it has to be addressed through drive voltage margin and the current closed loop.<\/p><p>My approach is to build the board-level thermal design solidly first and then talk about compensation. For example, the big heat producers such as power transistors, freewheeling transistors and current sampling resistors, I place separately on one side of the board and dissipate with thick copper regions, even going directly to a Heavy copper PCB supplier to proof at 2 oz or 3 oz copper. With local temperature rise lowered, the signal area is much less affected. On the multilayer side, I generally choose a multilayer pcb manufacturer that really knows power board processes, rather than casually finding a factory that can laminate. An ordinary multilayer board factory and a multilayer pcb supplier differ in their control of lamination thickness and inner-layer copper uniformity, and the thermal resistance distribution of the boards they make also differs. If there are loops on the board carrying continuous large current, I prefer to go directly to a Heavy copper PCB manufacturer to make the thick copper layers sufficient and not let an ordinary factory force it. Once I sent a board to a factory that had never made thick copper boards; it came back with thin inner-layer copper, the large-current traces ran very hot, and the temperature difference across the board surface measured more than ten degrees. Using such a board for temperature compensation is simply making trouble for yourself.<\/p><p>So my view is that for a hydraulic control board to stay stable as temperature changes, first separate the heat sources, give enough copper thickness and build the lamination structure well; this is more effective than adding any number of sensors and compensation algorithms later. Once the board&#8217;s own thermal time constant has stabilized, dealing with the drive issues on the coil side becomes much clearer.<\/p><p>When making hydraulic valve driver boards, I never pursue multi-channel temperature compensation. When I first started working on the Hydraulic Control System PCB, I measured board temperature and valve temperature separately and even added a dedicated conditioning circuit; after finishing I found the debugging difficulty had doubled while the actual benefit was small. Later a customer reported a repair on site, saying the valve action was unstable at low temperature. When I went to measure, the board temperature sensor was right next to the freewheeling diode, and the temperature it collected was almost thirty degrees higher than the average temperature of the board, so the compensation algorithm was completely misled.<\/p><p>After that I stopped believing in the number of sensors. What really matters for a board temperature sensor is not accuracy but position and consistency. I generally place it between the analog front end and the connector, away from power switches and large-current traces, so that it measures the temperature of a relatively stable zone. Being off by a few degrees in absolute temperature does not matter; as long as at every power-up and across different boards it measures the same thermal zone, the compensation is meaningful. Temperature drift compensation looks at the trend of change, not an absolute reference, and many people get this backward.<\/p><p>The multilayer side has even more pits. The default stackup given by a multilayer pcb manufacturer often has a thermal resistance much worse than you think. With the same design, switching to another multilayer pcb supplier and raising the inner-layer copper from 35 microns to 70 microns can make the temperature at the sensor position differ by more than ten degrees under the same load. If the board uses Heavy copper PCB, heat spreading is more intense, and the sensor reading is often a blurred value between local hot spots and cold zones. So when I talk with a Heavy copper PCB supplier now, I ask directly for thermal distribution data. Not every factory gives it, but if they cannot, subsequent calibration is basically impossible. I have also obtained several board-surface temperature scans from Heavy copper PCB manufacturer sources; a difference of twenty or so degrees between the large-current area and the sensor position is quite normal.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-5ecf32bf elementor-widget elementor-widget-image\" data-id=\"5ecf32bf\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"image.default\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<img decoding=\"async\" width=\"600\" height=\"400\" src=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp\" class=\"attachment-large size-large wp-image-12346\" alt=\"hydraulic control system pcb manufacturing equipment\" srcset=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp 600w, https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment-18x12.webp 18w\" sizes=\"(max-width: 600px) 100vw, 600px\" \/>\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-48a2433d elementor-widget elementor-widget-text-editor\" data-id=\"48a2433d\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<h2>Isolation, Return Paths and Mixed Analog-Power Layout<\/h2><p>I always feel that many discussions about hydraulic control boards steer in the wrong direction. Everyone likes to stare at the withstand-voltage rating of the isolation module, as if piling up the specification would make the board stable. In fact, in a Hydraulic Control System PCB, what is really hard is how to keep the return current from passing through the sampling area when the power loop and the AD channels are crowded on the same plane. Current is not like signal: current finds the lowest-impedance path by itself and does not follow the line you drew. Cutting the ground plane with a slit for isolation sometimes amounts to severing the return path, and the noise pops up somewhere else. I have stepped into this pit, and only later understood that isolation is not just a component parameter; it is a physical boundary in the layout.<\/p><p>When working with a multilayer pcb manufacturer, I no longer start by asking how many layers they can make or what line width and spacing they achieve. Those questions are meaningful for ordinary digital boards but are not the key for hydraulic control boards. I care more about whether they have made mixed analog and power boards, especially how vias and copper pours are arranged after the ground plane is split. A qualified multilayer pcb supplier will ask you in return: roughly how much is the drive loop current at the actuator end, whether the sensor ground and control ground need a single-point connection, and whether the primary-to-secondary spacing of the isolated power supply can meet the pollution degree. If the other party only quotes parameters and does not ask about your operating conditions, you can basically stop talking.<\/p><p>For the actuator part, I tend to look for a Heavy copper PCB supplier separately to handle current carrying and heat dissipation, and not try to share one copper thickness with the signal area. Thick copper is an advantage in the drive area, but near the AD pins it becomes trouble: soldering heat capacity is large, and fine-pitch pins are easily bridged with solder. Some Heavy copper PCB manufacturer will recommend a local thick-copper process, which is indeed a compromise, but the premise is that you leave enough distance between the thick-copper boundary and the isolation barrier; otherwise the creepage distance is easily eaten up by the copper.<\/p><p>Back to isolation: I do not think more is better. Every additional isolation barrier requires one more isolated power supply, one more keep-out zone and one more detour. The more channels there are, the more these costs multiply, and in the end the board is big and expensive, and the accuracy is not necessarily good. The stability of an AD channel comes more from reserving a clean return for each one in the layout than from piling up isolation devices. This is the biggest shift in my later work on hydraulic control boards: first think about which region the transient current should be confined to, and then decide where to put the isolation, rather than patching isolation everywhere after drawing the schematic.<\/p><p>I stepped into a very typical pit in a hydraulic station retrofit project. At the time I kept staring at the solenoid valve itself and overlooked the consistency of the reference level between the Hydraulic Control System PCB and the PLC. On site, every time one proportional valve acted, the pressure sensor signal jumped once and the value the PLC read went up and down, looking like the signal was being disturbed by the solenoid valve. In fact, hooking an oscilloscope onto the analog ground made it easy to see that the freewheeling current at coil turn-off did not take the shortest path back to the power supply but went around a big circle through the power plane in the PCB&#8217;s inner layer, lifting the signal ground by a very narrow spike. This problem could not be solved by switching to a board with thicker copper. Many a Heavy copper PCB supplier will recommend 3 oz or even 4 oz, but thick copper only lowers DC voltage drop and does limited good for controlling the path of transient circulating current. My later approach was first to have the multilayer pcb manufacturer lay power ground and signal ground separately, then make a single-point bridge near the analog input reference point of the PLC, and at the same time confine the coil freewheeling loop to the power side. This change demands a lot of the layout and cannot be squeezed onto an ordinary double-layer board. Later we found a multilayer pcb supplier that had made hydraulic control boards, whose stackup left one complete ground layer solely as the signal reference and used 2 oz copper on the power side, and the effect was clearly much better. Another, more hidden fault was that the PLC analog output directly gave the command to the proportional amplifier, while the amplifier itself was too close to the coil, and at high-current switching, spatial radiation coupled into the command line. Simply adding shielded cable was not thorough here either; the Heavy copper PCB manufacturer had to move the power stage close to the coil so that the PLC carried only low-current analog signals. My habit now is that whenever the board drives an inductive load above 1 A, I first draw out the return paths and ground partitioning clearly and only then talk about suppliers and copper thickness; otherwise even a more expensive board will still be the same as before.<\/p><p>I have worked on hydraulic control system boards for nearly ten years, and I have stepped into more pits on the Hydraulic Control System PCB than most engineers have eaten meals. A few years ago, what I believed in most was software algorithms; I thought as long as the DSP ran fast and the control strategy was written beautifully, the problems on the board could all be covered up. After being taught several lessons on site, I understood that the real bottleneck of this kind of board is all in the physical layer, especially the large-current paths and the isolation structure. Now when I look at a hydraulic control board, the first thing I look at is not the main controller model but the copper thickness, the trace width, the position of the isolation slot and how the drive loop is routed.<\/p><p>Back when I looked for multilayer board factories, I always thought every multilayer pcb manufacturer was about the same, and whoever quoted the lowest price got the job. Then one batch of boards came back where the copper traces of the solenoid drive channels reached over a hundred degrees under a 12 A continuous load, and the current sampling waveform on the oscilloscope was all glitches. When we opened it up, the inner-layer copper was simply not thick enough and the ground plane was chopped into bits. After that I began to seriously distinguish a multilayer pcb supplier from a Heavy copper PCB manufacturer that truly has heavy copper processing capability. Many suppliers merely take orders and forward them, do not do lamination and plating themselves, and hem and haw when asked about copper thickness and interlayer withstand voltage. The Heavy copper PCB supplier I cooperate with regularly now dares to make inner layers 4 oz or even 6 oz, the voltage drop of the large-current loop is clearly much smaller and the temperature rise is held down. This is a completely different concept from cheap boards.<\/p><p>On the current sampling side, many people think it is enough to put a sampling resistor in the low side. A hydraulic valve coil is a typical inductive load, and the recoil at the instant of PWM switching produces very steep spikes at the sampling point. If you do not separate the sampling ground and the power ground, the digital ground gets flooded into a mess. My approach is to put the current sampling loop entirely on the high-voltage side of the isolation barrier and send the signal to the DSP through an isolation amplifier. But here I want to correct a common misunderstanding: whether the isolation works well really does not depend on how cleanly you cut the copper under the isolation barrier. In my early years I also believed in a physical isolation slot, thinking that cutting a slot between high voltage and low voltage settled everything. Later there was a board whose isolation slot was made very standard, yet common-mode interference still reset the DSP. After searching everywhere, the problem lay in the parasitic capacitance of the isolated power module, where high-frequency common-mode current crossed the barrier directly through this capacitor. So now when I look at isolation, I first look at the bridging capacitance of the isolated power supply and how the reference grounds on both sides of the isolation device are handled, rather than staring only at the copper.\u00a0<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-37a46ca elementor-widget elementor-widget-heading\" data-id=\"37a46ca\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"heading.default\">\n\t\t\t\t\t<h2 class=\"elementor-heading-title elementor-size-default\">Frequently Asked Questions<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-212ae40 elementor-widget elementor-widget-elementskit-faq\" data-id=\"212ae40\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"elementskit-faq.default\">\n\t\t\t\t\t<div class=\"ekit-wid-con\" >\n                <div class=\"elementskit-single-faq elementor-repeater-item-9666b77\">\n           <div class=\"elementskit-faq-header\">\n                <h2 class=\"elementskit-faq-title\">\n                    Why do many Hydraulic Control System PCB faults look like control problems but turn out to be board problems?                <\/h2>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                Coil current, PWM switching and weak sampling signals share one substrate. If the power ground and sampling ground are not physically separated, return current lifts the sampling reference by millivolts and the feedback becomes dirty, so retuning the closed-loop gain cannot fix it. Redrawing the stackup and keeping the ground plane complete solved cases such as spool jitter on an injection molding machine.            <\/div>\n        <\/div>\n                <div class=\"elementskit-single-faq elementor-repeater-item-76f8a98\">\n           <div class=\"elementskit-faq-header\">\n                <h2 class=\"elementskit-faq-title\">\n                    What should I ask a heavy copper or multilayer PCB supplier before ordering a valve driver board?                <\/h2>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                Ask for inner-layer copper thickness tolerance, hot-press uniformity, copper-thickness cross-section reports, via reliability test data after thermal cycling, etch factor control, and whether they have built mixed heavy copper lamination or hydraulic and motor drive boards. A nominal copper weight alone is not enough, because uneven inner copper changes voltage drop and creates thermal drift in the sampling area.            <\/div>\n        <\/div>\n                <div class=\"elementskit-single-faq elementor-repeater-item-155437e\">\n           <div class=\"elementskit-faq-header\">\n                <h2 class=\"elementskit-faq-title\">\n                    How should power and signal grounds be arranged on a hydraulic control board?                <\/h2>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                Keep the ground plane intact, separate the power ground from the signal ground, and join them at a single point near the supply entry or the analog reference point. Place the freewheeling diode close to the coil terminal, keep the freewheeling and clamp loop small and on the power side, and put the clamp reference on the same low-impedance plane as the switch ground.            <\/div>\n        <\/div>\n                <div class=\"elementskit-single-faq elementor-repeater-item-05c1619\">\n           <div class=\"elementskit-faq-header\">\n                <h2 class=\"elementskit-faq-title\">\n                    Is thick copper enough to make the current loop stable on a Hydraulic Control System PCB?                <\/h2>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                No. Thick copper reduces DC voltage drop and improves heat spreading, but it does not control the path of transient circulating current, and it brings etching, lamination and drilling challenges. Stable loops come from the combination of layout, return paths, PWM and sampling timing, sensor placement, and a supplier with consistent copper thickness and via quality.            <\/div>\n        <\/div>\n                \n    <\/div>\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>","protected":false},"excerpt":{"rendered":"<p>Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.<\/p>","protected":false},"author":1,"featured_media":12346,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[51],"tags":[],"class_list":["post-12385","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blogs"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v28.9 (Yoast SEO v28.9) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards<\/title>\n<meta name=\"description\" content=\"Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.sprintpcbgroup.com\/ko\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/\" \/>\n<meta property=\"og:locale\" content=\"ko_KR\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards\" \/>\n<meta property=\"og:description\" content=\"Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.sprintpcbgroup.com\/ko\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/\" \/>\n<meta property=\"og:site_name\" content=\"SprintpcbGroup\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/profile.php?id=61582505616626\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-22T07:00:00+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp\" \/>\n\t<meta property=\"og:image:width\" content=\"600\" \/>\n\t<meta property=\"og:image:height\" content=\"400\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/webp\" \/>\n<meta name=\"author\" content=\"sprintpcbgroup\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@xipu386771\" \/>\n<meta name=\"twitter:site\" content=\"@xipu386771\" \/>\n<meta name=\"twitter:label1\" content=\"\uae00\uc4f4\uc774\" \/>\n\t<meta name=\"twitter:data1\" content=\"sprintpcbgroup\" \/>\n\t<meta name=\"twitter:label2\" content=\"\uc608\uc0c1 \ub418\ub294 \ud310\ub3c5 \uc2dc\uac04\" \/>\n\t<meta name=\"twitter:data2\" content=\"39\ubd84\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/\"},\"author\":{\"name\":\"sprintpcbgroup\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/person\\\/dafc2c514153973c78bd4a61a060fed4\"},\"headline\":\"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards\",\"datePublished\":\"2026-11-22T07:00:00+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/\"},\"wordCount\":8682,\"publisher\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/hydraulic-control-system-pcb-manufacturing-equipment.webp\",\"articleSection\":[\"blogs\"],\"inLanguage\":\"ko-KR\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/\",\"name\":\"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/hydraulic-control-system-pcb-manufacturing-equipment.webp\",\"datePublished\":\"2026-11-22T07:00:00+00:00\",\"description\":\"Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#breadcrumb\"},\"inLanguage\":\"ko-KR\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"ko-KR\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/hydraulic-control-system-pcb-manufacturing-equipment.webp\",\"contentUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/hydraulic-control-system-pcb-manufacturing-equipment.webp\",\"width\":600,\"height\":400,\"caption\":\"hydraulic control system pcb factory equipment display.\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#website\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/\",\"name\":\"SprintpcbGroup\",\"description\":\"One-stop supplier of high-end PCB manufacturing and assembly for small and medium batches.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"ko-KR\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#organization\",\"name\":\"SprintpcbGroup\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ko-KR\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/01\\\/sprintpcbgroup-pcb-manufacturer-site-icon.png\",\"contentUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/01\\\/sprintpcbgroup-pcb-manufacturer-site-icon.png\",\"width\":500,\"height\":500,\"caption\":\"SprintpcbGroup\"},\"image\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/profile.php?id=61582505616626\",\"https:\\\/\\\/x.com\\\/xipu386771\",\"https:\\\/\\\/www.linkedin.com\\\/company\\\/33304071\\\/admin\\\/page-posts\\\/published\\\/\",\"https:\\\/\\\/www.youtube.com\\\/@Sprint-PCB\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/person\\\/dafc2c514153973c78bd4a61a060fed4\",\"name\":\"sprintpcbgroup\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ko-KR\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g\",\"caption\":\"sprintpcbgroup\"},\"sameAs\":[\"https:\\\/\\\/www.sprintpcbgroup.com\"]}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards","description":"Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.sprintpcbgroup.com\/ko\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/","og_locale":"ko_KR","og_type":"article","og_title":"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards","og_description":"Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.","og_url":"https:\/\/www.sprintpcbgroup.com\/ko\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/","og_site_name":"SprintpcbGroup","article_publisher":"https:\/\/www.facebook.com\/profile.php?id=61582505616626","article_published_time":"2026-11-22T07:00:00+00:00","og_image":[{"width":600,"height":400,"url":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp","type":"image\/webp"}],"author":"sprintpcbgroup","twitter_card":"summary_large_image","twitter_creator":"@xipu386771","twitter_site":"@xipu386771","twitter_misc":{"\uae00\uc4f4\uc774":"sprintpcbgroup","\uc608\uc0c1 \ub418\ub294 \ud310\ub3c5 \uc2dc\uac04":"39\ubd84"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#article","isPartOf":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/"},"author":{"name":"sprintpcbgroup","@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/person\/dafc2c514153973c78bd4a61a060fed4"},"headline":"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards","datePublished":"2026-11-22T07:00:00+00:00","mainEntityOfPage":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/"},"wordCount":8682,"publisher":{"@id":"https:\/\/www.sprintpcbgroup.com\/#organization"},"image":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#primaryimage"},"thumbnailUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp","articleSection":["blogs"],"inLanguage":"ko-KR"},{"@type":"WebPage","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/","url":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/","name":"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards","isPartOf":{"@id":"https:\/\/www.sprintpcbgroup.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#primaryimage"},"image":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#primaryimage"},"thumbnailUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp","datePublished":"2026-11-22T07:00:00+00:00","description":"Practical field lessons on Hydraulic Control System PCB design: separating power and sampling grounds, choosing heavy copper and multilayer suppliers, PWM current loops, dither, temperature drift, port detection and isolation for proportional and servo valve drivers.","breadcrumb":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#breadcrumb"},"inLanguage":"ko-KR","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/"]}]},{"@type":"ImageObject","inLanguage":"ko-KR","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#primaryimage","url":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp","contentUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/hydraulic-control-system-pcb-manufacturing-equipment.webp","width":600,"height":400,"caption":"hydraulic control system pcb factory equipment display."},{"@type":"BreadcrumbList","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/hydraulic-control-system-pcb-heavy-copper-current-sampling-ground-return\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.sprintpcbgroup.com\/"},{"@type":"ListItem","position":2,"name":"Hydraulic Control System PCB Design and Sourcing: Ground Return, Heavy Copper, and Current Sampling Lessons for Multilayer Boards"}]},{"@type":"WebSite","@id":"https:\/\/www.sprintpcbgroup.com\/#website","url":"https:\/\/www.sprintpcbgroup.com\/","name":"SprintpcbGroup","description":"\uc911\uc18c\uaddc\ubaa8 \ubc30\uce58\uc6a9 \ud558\uc774\uc5d4\ub4dc PCB \uc81c\uc870 \ubc0f \uc870\ub9bd\uc744 \uc704\ud55c \uc6d0\uc2a4\ud1b1 \uacf5\uae09\uc5c5\uccb4\uc785\ub2c8\ub2e4.","publisher":{"@id":"https:\/\/www.sprintpcbgroup.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.sprintpcbgroup.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"ko-KR"},{"@type":"Organization","@id":"https:\/\/www.sprintpcbgroup.com\/#organization","name":"SprintpcbGroup","url":"https:\/\/www.sprintpcbgroup.com\/","logo":{"@type":"ImageObject","inLanguage":"ko-KR","@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/01\/sprintpcbgroup-pcb-manufacturer-site-icon.png","contentUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/01\/sprintpcbgroup-pcb-manufacturer-site-icon.png","width":500,"height":500,"caption":"SprintpcbGroup"},"image":{"@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/profile.php?id=61582505616626","https:\/\/x.com\/xipu386771","https:\/\/www.linkedin.com\/company\/33304071\/admin\/page-posts\/published\/","https:\/\/www.youtube.com\/@Sprint-PCB"]},{"@type":"Person","@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/person\/dafc2c514153973c78bd4a61a060fed4","name":"sprintpcbgroup","image":{"@type":"ImageObject","inLanguage":"ko-KR","@id":"https:\/\/secure.gravatar.com\/avatar\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g","caption":"sprintpcbgroup"},"sameAs":["https:\/\/www.sprintpcbgroup.com"]}]}},"_links":{"self":[{"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/posts\/12385","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/comments?post=12385"}],"version-history":[{"count":1,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/posts\/12385\/revisions"}],"predecessor-version":[{"id":12512,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/posts\/12385\/revisions\/12512"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/media\/12346"}],"wp:attachment":[{"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/media?parent=12385"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/categories?post=12385"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ko\/wp-json\/wp\/v2\/tags?post=12385"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}