{"id":12426,"date":"2026-11-17T15:00:00","date_gmt":"2026-11-17T07:00:00","guid":{"rendered":"https:\/\/www.sprintpcbgroup.com\/?p=12426"},"modified":"2026-11-17T11:29:19","modified_gmt":"2026-11-17T03:29:19","slug":"power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design","status":"publish","type":"post","link":"https:\/\/www.sprintpcbgroup.com\/ja\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/","title":{"rendered":"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies"},"content":{"rendered":"\t\t<div data-elementor-type=\"wp-post\" data-elementor-id=\"12426\" class=\"elementor elementor-12426\" data-elementor-post-type=\"post\">\n\t\t\t\t<div class=\"elementor-element elementor-element-65c6bff7 e-flex e-con-boxed e-con e-parent\" data-id=\"65c6bff7\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t\t<div class=\"e-con-inner\">\n\t\t\t\t<div class=\"elementor-element elementor-element-6b615ae3 elementor-widget elementor-widget-text-editor\" data-id=\"6b615ae3\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<p>On a Power Factor Correction PCB, efficiency and temperature rise are limited by copper thickness, current paths, commutation loop area and thermal via quality at least as much as by the choice of magnetic core, diode or topology. Swapping to SiC diodes or GaN switches without fixing the loop only makes ringing worse. Use heavy copper selectively where the power path needs it, keep signal and control areas at standard copper, and choose multilayer or heavy copper PCB suppliers by their evidence on inner-layer copper uniformity, lamination, thermal via barrel quality and thermal cycling adhesion.<\/p><h2>Copper Thickness and Stackup Come Before Topology<\/h2><p>After making several power supplies with active PFC, I increasingly feel that what the Power Factor Correction PCB tests most is not how new a topology you choose but how you communicate copper thickness and stackup to the PCB factory. Many people chase high efficiency from the start and overlook that once those few loops on the PFC PCB are drawn badly, even better switching transistors are in vain. Loss is especially real in PFC: when the current is large, a standard 1 oz copper trace heats up straight away, and only after I changed the power loop layers to 2 oz and locally even 3 oz was the temperature rise held down. Here is a real experience: with the same schematic, one made by an ordinary multilayer pcb manufacturer went into thermal protection after half an hour at full load; after switching to a Heavy copper PCB supplier that specializes in power boards, with only the stackup and inner-layer copper thickness changed and nothing else touched, the temperature dropped by more than ten degrees. This gap cannot be seen by design software.<\/p><p>So when I choose a multilayer pcb supplier now, I first ask whether they have made power boards with PFC, especially cases of heavy copper plus multilayer hybrid lamination. Many PCB factories say with their mouths that they can do it, but in reality their control of details such as lamination uniformity of inner-layer thick copper and via filling is poor. The loss of a PFC board is concentrated in the commutation loop, and if thermal vias are not filled well, the path for heat from the bottom of the power transistor to the back heatsink is cut directly. Rather than agonizing over which brand of SiC diode to choose, first confirm whether your Heavy copper PCB manufacturer can make the copper thickness uniform and whether the via copper wall is thick enough. Many failures never even come to the device itself.<\/p><p>I also do not recommend using heavy copper on the whole board. The PFC stage does need thick copper, but using thick copper for the control part and sampling traces instead increases processing difficulty, and the cost is outrageous. The reasonable approach is to have the PCB factory do local thick copper, that is, 2 to 3 oz for the key power paths and 1 oz for the signal area, which controls loss without sacrificing precision. Making local copper thickness on a multilayer board demands a fair amount from the process, so when looking for a <a href=\"https:\/\/www.sprintpcbgroup.com\/pcb-manufacturing\/multilayer-pcb\/\">multilayer pcb manufacturer<\/a>, look more at their past cross-section reports of power boards and do not just listen to salespeople saying they can do it.<\/p><p>When I later did similar projects I learned my lesson: for the PFC part of the design, do not just stare at efficiency numbers and topology labels; first think clearly about the PCB&#8217;s thermal path and copper thickness allocation, and with the right partner chosen, many problems can be avoided before prototyping. In the power supply business, when the board is made solidly, losses naturally come down and it also withstands being tossed around in volume.<\/p><h2>Magnetic Cores, Winding Loss and What the PCB Contributes<\/h2><p>I have made quite a few PFC circuits and found that many people start by drilling into core material comparisons, as if choosing the right ferrite or Sendust would solve everything. In fact, around 100 kHz, core loss does differ, but what truly makes me flop is often the power ground return path and the copper foil heating near the inductor pins. If a Power Factor Correction PCB has insufficient trace width and copper of only 1 oz, then even if you swap to a lower-loss core, the board temperature still will not come down. Especially in high-current PFC, the few centimeters of trace between the inductor pin and the MOSFET drain have a large current change rate, and the ringing caused by parasitic inductance is more of a headache than that bit of loss in the core itself.<\/p><p>I have dealt with several multilayer board suppliers, and some multilayer pcb manufacturer plants care only about layer count and line width and spacing and are not familiar with thick copper processes. Later I found a manufacturer that specializes in heavy copper to re-proof, raised the copper thickness of the PFC loop from 2 oz to 4 oz, and also filled and thickened the plating of the vias; under the same core conditions efficiency improved by less than half a point, but the hot spot temperature in the thermal imager dropped by nearly ten degrees. This difference was not given by the core; it was given by the PCB. Many a Heavy copper PCB supplier in fact already has ready-made large-current process capability, but many people did not communicate clearly in advance, and only after the design was finished did they find it could not be made or the yield was very low.<\/p><p>Back to the core itself: Sendust with a distributed air gap between 50 and 100 kHz can indeed reduce the extra winding heating caused by fringing flux, and I agree with that. But the problem is that if your winding structure is unreasonable, such as winding multi-strand wire carelessly or not making full use of the copper foil in the window, the little saved in core loss is soon eaten up by winding AC loss. My own habit is to first determine the winding current density and AC impedance and then work backward to the core air gap rather than locking in a material first. A ferrite with a large air gap is not entirely unusable; it is just more sensitive to winding and PCB layout and needs more careful simulation and measurement.<\/p><p>Above 100 kHz, things change: the proportion of core loss rises, and then ferrite or nanocrystalline is worth a serious evaluation. But as soon as the frequency goes up, MOSFET switching loss, drive loop parasitics and the pressure on the EMI filter all change together, and it is by no means done by just changing the core. I have seen someone use Sendust for PFC at 200 kHz and the efficiency was not much worse, because his PFC PCB pressed the power loop very small, with low stray inductance and well-controlled ringing. So my view is that the core material is one variable, but the dumb work of PCB copper thickness, stackup, via design and winding process often decides whether the product can be mass produced. Rather than spend a lot of time agonizing over the core loss curve, it is better to first ask the multilayer pcb supplier clearly about thick copper tolerance and lamination structure, and then confirm with the Heavy copper PCB manufacturer how the openings and heat-spreading copper of high-current traces are handled.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-7c7b166c elementor-widget elementor-widget-image\" data-id=\"7c7b166c\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"image.default\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<img fetchpriority=\"high\" decoding=\"async\" width=\"600\" height=\"400\" src=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp\" class=\"attachment-large size-large wp-image-12363\" alt=\"power factor correction pcb pfc pcb products\" srcset=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp 600w, https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products-18x12.webp 18w\" sizes=\"(max-width: 600px) 100vw, 600px\" \/>\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-57fc74fa elementor-widget elementor-widget-text-editor\" data-id=\"57fc74fa\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<h2>Heavy Copper Limits, Etching and Warpage<\/h2><p>In my years of working on PFC circuits, my biggest feeling is that people put too much attention on topology and control, while what really drags down the project schedule is often the board itself. After a <a href=\"https:\/\/www.sprintpcbgroup.com\/pcb-applications\/new-energy-power-electronics-pcb\/\">Power Factor Correction PCB<\/a> is drawn, if the PCB factory has no power board experience, what comes out may have substandard copper thickness and uneven inner-layer copper thickness, and after power-on local heating occurs when current is large. But people on the design side often realize only at the debugging stage that the problem is not in the devices but in manufacturing coordination.<\/p><p>My own habit is that before choosing a multilayer pcb manufacturer, I first confirm whether they have made power boards with thick copper inner layers. Many manufacturers that make ordinary digital boards apply their lamination and etching parameters directly, and the PFC PCB they make passes electrical testing, but after a few thermal cycles delamination begins between the inner copper and the dielectric. This problem is harder to find than a schematic error. A multilayer board is not more advanced the more layers it has; for PFC the key is the current-carrying capacity of the inner-layer copper and the continuity of interlayer heat conduction. Some suppliers can laminate 12 layers but are willing to make inner-layer copper only up to 2 oz, which is simply not enough for a high-current PFC. When looking for a multilayer pcb supplier, I would rather choose a factory that is not large but specializes in power boards, which understands the relationship among copper thickness, board bow and heat dissipation.<\/p><p>The water in thick copper boards is deeper. Among Heavy copper PCB manufacturer plants, few can truly make copper of 6 oz and above uniform. After the copper gets too thick, the etch factor of the line width gets worse, and the safety spacing you left in the design may be eaten away by a section on the actual board. Then there is the board bow problem: thick copper boards easily warp after reflow, gaps appear in the mating surface between the heatsink and power devices, and thermal resistance goes out of control directly. So I do not much believe in blindly adding copper thickness; if a <a href=\"https:\/\/www.sprintpcbgroup.com\/pcb-manufacturing\/thick-copper-pcb\/\">Heavy copper PCB supplier<\/a> only brags about the maximum ounces of copper but cannot explain etch compensation and lamination process, I will steer clear of that kind of supplier. However high the power density, copper thickness has to have a limit; the key is still to keep the current path short and give the heat somewhere to go.<\/p><h2>SiC Diodes, Commutation Loops and Layout Sensitivity<\/h2><p>Speaking of diodes, many people working on PFC get a headache whenever silicon fast-recovery diodes come up with reverse recovery in CCM mode, and that does exist. But a phenomenon I have observed is that quite a few people treat SiC Schottky diodes as a universal cure, as if switching to them would naturally lift efficiency. In fact, if the parasitic inductance of the commutation loop is not controlled, the turn-on and turn-off slopes of a SiC diode are very steep, and the ringing is instead worse than with silicon devices, and the EMI problem may be worse. The reverse recovery characteristic of a diode is only part of the whole commutation loop; in the layout, the distance from the diode to the MOSFET and the storage capacitor and the area enclosed by the traces affect efficiency no less than the device itself. I have seen a board where efficiency could not go up with silicon FRD, and after switching to SiC efficiency improved only a tiny bit, and only after shortening the copper between the diode and the transistor and shrinking the loop area by nearly half did efficiency truly lift.<\/p><p>So when I draw a PFC PCB, I first deliberate repeatedly over the placement of the MOSFET, diode and output capacitor, trying to make the commutation path shortest, and consider other things after that. The pads and vias of the diode also need thermal management while we are at it, otherwise the transistor is not hot but the diode cannot hold up first. The number of thermal vias is of course important, but barrel wall quality, whether they are plugged, and with what material, are the details that decide whether heat can truly be conducted from the device junction to the back copper layer. Some people drill a pile of vias on the board and, with no fill in the holes, solder is wicked away during reflow, the power terminal gets a cold joint, and thermal resistance instead becomes larger. This kind of problem is hard to find by conventional testing and is often exposed only after loaded aging.<\/p><p><span style=\"font-family: inherit; font-size: inherit; font-style: inherit; font-variant-ligatures: inherit; font-variant-caps: inherit; font-weight: inherit;\">My exposure to SiC diodes was on a 600 W communication power supply project, when someone on the team thought switching to SiC would lift PFC efficiency by a notch. When we ran it, the efficiency improvement was not as obvious as imagined, and instead the ringing on the switching node was exposed first. My view is that whether SiC can play a role in a PFC circuit depends not on the device itself but on how the commutation loop of that Power Factor Correction PCB is routed. Many people overlook this, thinking that swapping one device finishes the job, and as a result the waveform is a mess.<\/span><\/p><p>During that debugging, I removed the original silicon fast-recovery diode and put in SiC, and the spike of reverse recovery current did become much lower, but at MOSFET turn-on a noticeable high-frequency oscillation could still be seen, with no small amplitude. After checking around, the problem was in the PFC PCB layout. There was a distance between the diode and the switching transistor, the commutation loop wrapped around a circle, and the parasitic inductance was roughly a dozen-odd nH. SiC switches fast and excites these parasitics even more strongly. Later I placed the diode right against the MOSFET and shrank the loop area to the minimum, and the ringing was suppressed. This experience made me realize that SiC&#8217;s tolerance to layout is much lower than that of silicon devices, and every millimeter of the commutation loop has to be scrutinized.<\/p><p>Once power density goes up, simply thickening traces on a double-sided board is no longer enough. For this kind of power supply I now basically look for a pcb manufacturer that can do both thick copper and multilayer for prototypes. Put the power loop on an inner layer and use 2 oz or even 3 oz copper to carry the current, leaving the outer layers for signal and control. The benefit is that the stackup can control loop area while the current-carrying capacity is much stronger than that of an ordinary 1 oz board. But not every multilayer pcb supplier is willing to make thick-copper inner layers, many doing only the standard process; while some Heavy copper PCB manufacturer plants are only good at double-sided boards and cannot make stackups above six layers. So you have to find a Heavy copper PCB supplier with both capabilities, and when looking for a supplier you must ask clearly about details such as minimum line width, copper thickness uniformity and insulation layer thickness. I have been burned: one factory sent boards whose inner-layer copper was nominally 2 oz, but measured only 1.6 oz locally, so the voltage drop was large at full load and efficiency directly dropped a few tenths of a point.<\/p><p>On parallel current sharing, the temperature drift characteristic of SiC is indeed friendlier than silicon FRD by more than a little. When silicon devices are paralleled, once one device is slightly hotter, its VF drops and current surges toward it, a vicious cycle. SiC is the opposite: when temperature rises the voltage drop increases slightly, and current naturally spreads toward the cooler one. But my experience is that you cannot rely entirely on material characteristics. If the copper area under the packages of the paralleled diodes is asymmetric, or one side is near the fan while the other is blocked from the airflow by a capacitor, thermal balance will still go off. Current distribution during commutation is also not determined only by static VF, and dynamic parameter differences are amplified at high frequency. So the parallel layout must be symmetrical, with pads and thermal channels all consistent, and preferably the several devices should share one complete copper surface.<\/p><p>Looking back, the benefits SiC brings to PFC are real, but the release of its value depends highly on PCB process and layout details. Whether it is the commutation loop, the thick-copper inner layer or the symmetry of paralleling, all must be treated seriously at the board-drawing stage. My habit now is that, before the devices are even decided, I first communicate the stackup and copper thickness scheme with the multilayer pcb manufacturer and then work backward to decide the device package and placement. This is much smoother than choosing devices first and then fitting the board around them, and has fewer detours. In power supplies, in the end it is details that compete.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-63b38248 elementor-widget elementor-widget-image\" data-id=\"63b38248\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"image.default\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<img decoding=\"async\" width=\"600\" height=\"400\" src=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-manufacturing-equipment.webp\" class=\"attachment-large size-large wp-image-12362\" alt=\"power factor correction pcb pfc pcb manufacturing equipment\" srcset=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-manufacturing-equipment.webp 600w, https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-manufacturing-equipment-18x12.webp 18w\" sizes=\"(max-width: 600px) 100vw, 600px\" \/>\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-5d36d7ed elementor-widget elementor-widget-text-editor\" data-id=\"5d36d7ed\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<h2>Thermal Resistance Paths and Double-Sided Cooling<\/h2><p>When many people work on high-power supplies, their first reaction is to switch to better switching transistors or diodes, but my own habit is to look at the Power Factor Correction PCB itself first. The traces, copper thickness and via distribution on a PFC PCB decide whether the heat produced by the devices can be dissipated smoothly. Thermal resistance cannot be judged by staring only at the device datasheet; the thermal resistance path on the board is often the biggest pit.<\/p><p>I was burned early on, always thinking that a low device thermal resistance marked on the datasheet settled everything, but when the board ran, local temperatures were still outrageously high. Only later did I understand that from the chip pad to the environment heat has to pass through too many interfaces, and the copper foil thickness and area of the PCB directly decide the efficiency of lateral heat dissipation. With the same power loop, placed on an ordinary thin copper board versus a thick copper board, the junction temperature gap is more obvious than changing the package. So when I later designed the high-current PFC part, the first thing I did was confirm copper thickness and the way heat-spreading copper is laid with the PCB factory.<\/p><p>When looking for a Heavy copper PCB manufacturer to make boards, you cannot look only at the copper thickness number. In processing thick copper, etching precision is somewhat worse, and interlayer dielectric filling is also prone to problems. A good Heavy copper PCB supplier will put effort into side-etch control and dielectric filling of thick copper; otherwise the trace edges are rough, current distribution is uneven, and both heat dissipation and reliability suffer. I generally ask them to provide cross-section reports of the thick copper to see the real copper shape. This step cannot be skipped, especially at the prototype stage.<\/p><p>The role of multilayer boards in heat dissipation is underestimated by many people. Large copper planes on inner layers can spread heat laterally, much better than relying on surface copper alone. When communicating with a multilayer pcb supplier, I specifically ask that heat-spreading copper be arranged on the inner layers, rather than treating the inner layers only as signal layers. The level at which different multilayer pcb manufacturer plants make thermal vias differs quite a lot, and details such as via copper thickness and resin plugging quality directly affect thermal resistance. Some PCB factories care only whether the layer count is right and whether line width and spacing are enough, and have no concept at all of thermal design parameters; working with them is especially tiring.<\/p><p>Double-sided cooling packages have been discussed a lot in the last two years, and I admit it can indeed improve the thermal path, but there is no need to treat it as a cure-all. Top-side cooling has to go through a thermal pad and the enclosure, and bottom-side cooling still has to go through the PCB, and whichever section has high thermal resistance will become the bottleneck. If the bottom copper plane is not well connected to the vias, or the inner layers of a thick copper board do not take part in heat dissipation, then however low the thermal resistance of the package, it cannot be exploited. So I prefer to see double-sided cooling as the result of system cooperation rather than the upgrade of a single device. In many cases, first pressing down the PCB&#8217;s thermal resistance gives results more stable than rushing to change the package.<\/p><p>When all is said and done, the thermal design of a Power Factor Correction PCB is a whole-picture job. When choosing a supplier, I look at thermal management capability, thick copper process and multilayer board manufacturing capability together, rather than comparing only copper thickness and price. The rework and time saved this way are far more cost-effective than groping around by myself.<\/p><h2>Totem-Pole PFC Is Not a Cure-All<\/h2><p>In the years I have worked with the Power Factor Correction PCB, I increasingly feel that people have deified totem-pole PFC. It seems that once you use a totem pole, efficiency, EMI and heat are all solved automatically. In fact, if the current paths on the board are not straightened out, changing any topology is in vain. I once flopped on a 400 W class power supply: to catch the schedule, I casually found a multilayer pcb supplier and sent out drawings with a conventional stackup. As a result the copper width in the PFC part was insufficient and the vias were sparse, and at full load the local temperature rise directly forced the test to stop. Later I switched to a manufacturer that specializes in Heavy copper PCB and raised the key power layers to 4 oz, and things eased. That was not a package or topology problem; it was that the current-carrying capacity of the PFC PCB had not kept up.<\/p><p>Some people ask me what to look at when choosing a multilayer pcb manufacturer. My standard is very practical: whether they have made high-current power boards, especially PFC front stages.\u00a0<\/p><p>After tuning several power boards with PFC, I increasingly feel that when choosing topology many people actually overlook something more solid: the Power Factor Correction PCB itself is the weak link limiting efficiency. However beautifully the efficiency of a totem-pole PFC is calculated in simulation, on the board, if the power loop goes around half a turn more of copper, the parasitic inductance goes up, obvious ringing can be seen in the GaN switching waveform, and efficiency drops by no small amount. So when I look at a scheme now, I first ask what the PCB can be made into and only then talk about device loss.<\/p><p><span style=\"font-family: inherit; font-size: inherit; font-style: inherit; font-variant-ligatures: inherit; font-variant-caps: inherit; font-weight: inherit;\">I was recently modifying a PFC PCB, and only at the third version did I realize the problem was not in the control loop at all. After running at full load for half an hour, the area near the PFC inductor was more than ten degrees hotter than elsewhere, clearly perceptible even by hand. When the board was removed and cross-sectioned, there was already minute delamination between the inner-layer thick copper and the resin, and that is not something a component swap can solve.<\/span><\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-70a5206d elementor-widget elementor-widget-image\" data-id=\"70a5206d\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"image.default\">\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<img decoding=\"async\" width=\"600\" height=\"400\" src=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-inspection-equipment.webp\" class=\"attachment-large size-large wp-image-12361\" alt=\"power factor correction pcb pfc pcb inspection equipment\" srcset=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-inspection-equipment.webp 600w, https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-inspection-equipment-18x12.webp 18w\" sizes=\"(max-width: 600px) 100vw, 600px\" \/>\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-72074278 elementor-widget elementor-widget-text-editor\" data-id=\"72074278\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t\t\t\t\t\t<h2>Surge Paths and Inner-Layer Copper<\/h2><p>The biggest pit I have stepped into in power supply projects was not choosing the wrong relay or thyristor but drawing the surge path of the Power Factor Correction PCB as an ordinary signal line. Many people, when tuning PFC circuits, stare at the trigger timing and withstand capability of devices, but how copper is routed inside the board and how the ground plane is cut have an effect on voltage spikes that is seriously underestimated. The inrush current at the instant of turn-on may last only a few milliseconds, but the induced spikes it produces on an unreasonable routing path are often harder to deal with than the withstand voltage marked in the device datasheet.<\/p><p>Once, when a prototype came back for a surge test, the loop around the relay bypass resistor always hit the capacitor behind it so that it screamed. The schematic was fine and the device margin was enough; later, when I caught the ground plane with an oscilloscope, I found the ground was not flat at the instant of turn-on, with a few volts of local jumping. The reason was simple: the multilayer pcb supplier at the beginning had given a standard stackup with 1 oz inner-layer copper, and the power ground crossed several vias before returning to the negative terminal of the large capacitor; under surge current, vias and long traces are inductance. Later I switched to a factory able to be a Heavy copper PCB manufacturer, changed the inner layer of the surge path to 3 oz copper, and kept the ground plane complete and unsplit; with the same circuit and the same devices, the spikes dropped by a large margin.<\/p><p>So when I look at a PFC PCB now, my first reaction is not to agonize over which of the relay and thyristor is more reliable but first to confirm whether the PCB factory can make the power loop correctly. When talking about the stackup with a multilayer pcb manufacturer, I explicitly require that the surge path must not use ordinary thickness and must be thickened separately; if the power is large, I simply find a Heavy copper PCB supplier to make thick-copper inner layers, which costs a bit more but saves trouble. Voltage and surge cannot be withstood just by switching to larger transistors; with a short current path at the instant of turn-on, enough copper thickness and a complete ground plane, many problems never appear.<\/p><h2>Mass Production Consistency of PFC Boards<\/h2><p>Of the several PFC boards I have handled in the last two years, what was truly hard to deal with was not topology or device loss but the hard-to-see deviations in the PCB manufacturing process. PFC current has a strong pulsed component, and if copper foil distribution is slightly disordered, hot spots move around and efficiency also drops.<\/p><p>When choosing a multilayer pcb manufacturer, most people stare only at layer count and minimum line width, but for a power factor correction circuit board I think one should focus more on the distribution of copper in the stackup. There was a board where the PCB factory, following the habit for ordinary multilayer boards, made the inner-layer copper thin, so that the PFC power ground return path was narrow and winding, and the switching node ringing was considerably greater than in simulation. Later I switched to a multilayer pcb supplier willing to adjust the stackup with a power mindset, thickening the two layers near the power layer, and the situation improved.<\/p><p>Thick copper is not better the thicker it is, either. When communicating with a Heavy copper PCB supplier, the other party always asks how many ounces are needed, but I care more about the etch compensation of inner-layer thick copper and the board thickness uniformity after lamination. Once the inner-layer copper is thick, interlayer registration and warpage are more sensitive, and if a Heavy copper PCB manufacturer merely thickens the copper without changing the lamination parameters, thermal resistance will clearly scatter over volume. With the same layout and different batches, the maximum temperature near the PFC inductor under the thermal imager could differ by several degrees; on cutting open, the copper thickness was fine, and the difference was in dielectric thickness and copper continuity.<\/p><p>Thermal resistance on a PFC PCB cannot be judged by the nominal value alone. I prefer to split it into two parts, lateral spreading and vertical interface. If a local hot spot relies only on thermal vias to pour heat downward while the surrounding copper is split into small islands, heat cannot spread laterally and, however thick the bottom copper, it is in vain. So my habit is to make the area under the PFC switch and diode a continuous copper island, letting the heat spread first and then be conducted away, which is more practical than blindly increasing copper thickness.<\/p><p>The mass production consistency of a Power Factor Correction PCB mostly gets stuck on how deeply the supplier understands power boards. When I look for a Heavy copper PCB manufacturer or multilayer pcb supplier now, I first ask whether they have made similar PFC boards, how they control residual copper rate and how they evaluate copper foil adhesion after thermal cycling. Under long-term thermal shock, stress accumulation between copper foil and dielectric layers in a PFC circuit changes the stability of thermal resistance, which is more worth caring about than the initial temperature rise.<\/p><p><span style=\"font-family: inherit; font-size: inherit; font-style: inherit; font-variant-ligatures: inherit; font-variant-caps: inherit; font-weight: inherit;\">I used to always feel that a PFC circuit not done well was a device selection problem, and then in a 2 kW power supply project I was educated by reality. The problem lay in the PFC PCB itself, especially the commutation loop section, where a slightly longer trace made the ringing too big to look at. Later I repaved the return path of that part, did not change any transistor, and the waveform became clean. This made me change my view completely.<\/span><\/p><p>On the commutation loop, many people start by pursuing the minimum enclosed area, but I now feel one should leave a little margin. If too compact, all the heat piles up in one corner and heat dissipation is more troublesome. Especially when using a thick copper board, with higher copper thickness the line width can be reduced a bit, but the heat conduction path changes with it, and thicker is not always better. I have seen a colleague raise the inner-layer copper to 4 oz, and as a result the via thermal resistance did not keep up, all the heat was stuffed in the surface layer, and in the end a heatsink had to be added.<\/p><p>I have not avoided pits in looking for manufacturers either. I have dealt with several Heavy copper PCB supplier plants; some mark inner-layer copper thickness very high but make thermal vias very casually, with small vias not even copper-paste plugged, and as a result, after the top-cooled package was attached, heat simply could not be conducted to the back. Later I switched to a Heavy copper PCB manufacturer that specializes in power boards, which was willing to make thickened copper on inner layers and also controlled the via barrel copper thickness, and only then was the junction temperature pressed down. So when I look at a PCB factory now, I first look at their thermal via cross-sections and then at copper thickness parameters.<\/p><p>I was especially optimistic about the double-sided cooling concept at the beginning, feeling it could solve many thermal problems, but in practice I found the manufacturing threshold higher than imagined. The contact thermal resistance between the top heatsink and the package surface is hard to stabilize and differs a lot between batches. The thermal resistance data provided by many a multilayer pcb manufacturer is measured under ideal conditions, and once installed in a chassis with a thermal pad added, it is not like that at all.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-1efb9cd elementor-widget elementor-widget-heading\" data-id=\"1efb9cd\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"heading.default\">\n\t\t\t\t\t<h2 class=\"elementor-heading-title elementor-size-default\">Frequently Asked Questions<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-d14fdda elementor-widget elementor-widget-elementskit-faq\" data-id=\"d14fdda\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"elementskit-faq.default\">\n\t\t\t\t\t<div class=\"ekit-wid-con\" >\n                <div class=\"elementskit-single-faq elementor-repeater-item-4904e0b\">\n           <div class=\"elementskit-faq-header\">\n                <h3 class=\"elementskit-faq-title\">\n                    Why does a Power Factor Correction PCB run hot even with a better core, diode or topology?                <\/h3>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                Heat is often generated and trapped in the board: thin copper, narrow traces, a long commutation loop and poor thermal vias raise temperature regardless of device quality. In several cases, raising loop copper from 2 oz to 4 oz and filling and thickening vias cut hot-spot temperature by nearly ten degrees with almost no efficiency change from the magnetics.            <\/div>\n        <\/div>\n                <div class=\"elementskit-single-faq elementor-repeater-item-7fc0ffc\">\n           <div class=\"elementskit-faq-header\">\n                <h3 class=\"elementskit-faq-title\">\n                    Does switching to SiC or GaN automatically improve PFC efficiency?                <\/h3>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                No. These devices switch fast, so any parasitic inductance in the commutation loop is excited harder and ringing can get worse than with silicon. Place the diode tight against the MOSFET, minimize loop area and keep every millimeter of the loop under review before expecting efficiency gains.            <\/div>\n        <\/div>\n                <div class=\"elementskit-single-faq elementor-repeater-item-163bea4\">\n           <div class=\"elementskit-faq-header\">\n                <h3 class=\"elementskit-faq-title\">\n                    When should heavy copper be used on a PFC board, and what are the limits?                <\/h3>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                Use it selectively: 2 to 3 oz or more on key power paths, standard copper for signal and control areas. Very thick copper reduces etch factor, can eat into design spacing, increases lamination and warpage sensitivity, and needs matching via and thermal design. Ask for cross-section reports, etch compensation details and inner-layer copper uniformity instead of only the maximum ounces.            <\/div>\n        <\/div>\n                <div class=\"elementskit-single-faq elementor-repeater-item-7defe86\">\n           <div class=\"elementskit-faq-header\">\n                <h3 class=\"elementskit-faq-title\">\n                    What should I ask a PCB supplier before prototyping a PFC power board?                <\/h3>\n            <\/div>\n            <div class=\"elementskit-faq-body\">\n                Ask whether they have made PFC or similar high-current boards with heavy copper plus multilayer lamination, how they control inner-layer copper thickness tolerance and residual copper rate, thermal via barrel thickness and plugging, copper foil adhesion after thermal cycling, and ask for per-batch dielectric thickness data and thermal via cross-sections.            <\/div>\n        <\/div>\n                                <script type=\"application\/ld+json\">{\"@context\":\"https:\/\/schema.org\",\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"Why does a Power Factor Correction PCB run hot even with a better core, diode or topology?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Heat is often generated and trapped in the board: thin copper, narrow traces, a long commutation loop and poor thermal vias raise temperature regardless of device quality. In several cases, raising loop copper from 2 oz to 4 oz and filling and thickening vias cut hot-spot temperature by nearly ten degrees with almost no efficiency change from the magnetics.\"}},{\"@type\":\"Question\",\"name\":\"Does switching to SiC or GaN automatically improve PFC efficiency?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"No. These devices switch fast, so any parasitic inductance in the commutation loop is excited harder and ringing can get worse than with silicon. Place the diode tight against the MOSFET, minimize loop area and keep every millimeter of the loop under review before expecting efficiency gains.\"}},{\"@type\":\"Question\",\"name\":\"When should heavy copper be used on a PFC board, and what are the limits?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Use it selectively: 2 to 3 oz or more on key power paths, standard copper for signal and control areas. Very thick copper reduces etch factor, can eat into design spacing, increases lamination and warpage sensitivity, and needs matching via and thermal design. Ask for cross-section reports, etch compensation details and inner-layer copper uniformity instead of only the maximum ounces.\"}},{\"@type\":\"Question\",\"name\":\"What should I ask a PCB supplier before prototyping a PFC power board?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Ask whether they have made PFC or similar high-current boards with heavy copper plus multilayer lamination, how they control inner-layer copper thickness tolerance and residual copper rate, thermal via barrel thickness and plugging, copper foil adhesion after thermal cycling, and ask for per-batch dielectric thickness data and thermal via cross-sections.\"}}]}<\/script>\n                \n    <\/div>\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t","protected":false},"excerpt":{"rendered":"<p>Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.<\/p>","protected":false},"author":1,"featured_media":12363,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[51],"tags":[],"class_list":["post-12426","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blogs"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v28.8 (Yoast SEO v28.8) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies<\/title>\n<meta name=\"description\" content=\"Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.sprintpcbgroup.com\/ja\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/\" \/>\n<meta property=\"og:locale\" content=\"ja_JP\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies\" \/>\n<meta property=\"og:description\" content=\"Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.sprintpcbgroup.com\/ja\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/\" \/>\n<meta property=\"og:site_name\" content=\"SprintpcbGroup\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/profile.php?id=61582505616626\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-17T07:00:00+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp\" \/>\n\t<meta property=\"og:image:width\" content=\"600\" \/>\n\t<meta property=\"og:image:height\" content=\"400\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/webp\" \/>\n<meta name=\"author\" content=\"sprintpcbgroup\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@xipu386771\" \/>\n<meta name=\"twitter:site\" content=\"@xipu386771\" \/>\n<meta name=\"twitter:label1\" content=\"\u57f7\u7b46\u8005\" \/>\n\t<meta name=\"twitter:data1\" content=\"sprintpcbgroup\" \/>\n\t<meta name=\"twitter:label2\" content=\"\u63a8\u5b9a\u8aad\u307f\u53d6\u308a\u6642\u9593\" \/>\n\t<meta name=\"twitter:data2\" content=\"25\u5206\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/\"},\"author\":{\"name\":\"sprintpcbgroup\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/person\\\/dafc2c514153973c78bd4a61a060fed4\"},\"headline\":\"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies\",\"datePublished\":\"2026-11-17T07:00:00+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/\"},\"wordCount\":5372,\"publisher\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/power-factor-correction-pcb-pfc-pcb-products.webp\",\"articleSection\":[\"blogs\"],\"inLanguage\":\"ja\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/\",\"name\":\"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/power-factor-correction-pcb-pfc-pcb-products.webp\",\"datePublished\":\"2026-11-17T07:00:00+00:00\",\"description\":\"Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#breadcrumb\"},\"inLanguage\":\"ja\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"ja\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/power-factor-correction-pcb-pfc-pcb-products.webp\",\"contentUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/power-factor-correction-pcb-pfc-pcb-products.webp\",\"width\":600,\"height\":400,\"caption\":\"power factor correction pcb pfc pcb display.\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/blogs\\\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#website\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/\",\"name\":\"SprintpcbGroup\",\"description\":\"One-stop supplier of high-end PCB manufacturing and assembly for small and medium batches.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"ja\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#organization\",\"name\":\"SprintpcbGroup\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ja\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/01\\\/sprintpcbgroup-pcb-manufacturer-site-icon.png\",\"contentUrl\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/wp-content\\\/uploads\\\/2026\\\/01\\\/sprintpcbgroup-pcb-manufacturer-site-icon.png\",\"width\":500,\"height\":500,\"caption\":\"SprintpcbGroup\"},\"image\":{\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/profile.php?id=61582505616626\",\"https:\\\/\\\/x.com\\\/xipu386771\",\"https:\\\/\\\/www.linkedin.com\\\/company\\\/33304071\\\/admin\\\/page-posts\\\/published\\\/\",\"https:\\\/\\\/www.youtube.com\\\/@Sprint-PCB\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.sprintpcbgroup.com\\\/#\\\/schema\\\/person\\\/dafc2c514153973c78bd4a61a060fed4\",\"name\":\"sprintpcbgroup\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ja\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g\",\"caption\":\"sprintpcbgroup\"},\"sameAs\":[\"https:\\\/\\\/www.sprintpcbgroup.com\"]}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies","description":"Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.sprintpcbgroup.com\/ja\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/","og_locale":"ja_JP","og_type":"article","og_title":"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies","og_description":"Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.","og_url":"https:\/\/www.sprintpcbgroup.com\/ja\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/","og_site_name":"SprintpcbGroup","article_publisher":"https:\/\/www.facebook.com\/profile.php?id=61582505616626","article_published_time":"2026-11-17T07:00:00+00:00","og_image":[{"width":600,"height":400,"url":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp","type":"image\/webp"}],"author":"sprintpcbgroup","twitter_card":"summary_large_image","twitter_creator":"@xipu386771","twitter_site":"@xipu386771","twitter_misc":{"\u57f7\u7b46\u8005":"sprintpcbgroup","\u63a8\u5b9a\u8aad\u307f\u53d6\u308a\u6642\u9593":"25\u5206"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#article","isPartOf":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/"},"author":{"name":"sprintpcbgroup","@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/person\/dafc2c514153973c78bd4a61a060fed4"},"headline":"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies","datePublished":"2026-11-17T07:00:00+00:00","mainEntityOfPage":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/"},"wordCount":5372,"publisher":{"@id":"https:\/\/www.sprintpcbgroup.com\/#organization"},"image":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#primaryimage"},"thumbnailUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp","articleSection":["blogs"],"inLanguage":"ja"},{"@type":"WebPage","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/","url":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/","name":"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies","isPartOf":{"@id":"https:\/\/www.sprintpcbgroup.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#primaryimage"},"image":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#primaryimage"},"thumbnailUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp","datePublished":"2026-11-17T07:00:00+00:00","description":"Lessons from real PFC projects: how copper weight, inner-layer thick copper, thermal vias, commutation loop layout, and SiC or GaN switching edges decide efficiency and temperature rise. Learn what to ask heavy copper and multilayer PCB suppliers before prototyping.","breadcrumb":{"@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#breadcrumb"},"inLanguage":"ja","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/"]}]},{"@type":"ImageObject","inLanguage":"ja","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#primaryimage","url":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp","contentUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/11\/power-factor-correction-pcb-pfc-pcb-products.webp","width":600,"height":400,"caption":"power factor correction pcb pfc pcb display."},{"@type":"BreadcrumbList","@id":"https:\/\/www.sprintpcbgroup.com\/blogs\/power-factor-correction-pcb-heavy-copper-commutation-loop-thermal-design\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.sprintpcbgroup.com\/"},{"@type":"ListItem","position":2,"name":"Power Factor Correction PCB Design Guide: Heavy Copper, Commutation Loop Layout and Thermal Paths for PFC Power Supplies"}]},{"@type":"WebSite","@id":"https:\/\/www.sprintpcbgroup.com\/#website","url":"https:\/\/www.sprintpcbgroup.com\/","name":"SprintpcbGroup","description":"\u5c0f\u30fb\u4e2d\u30ed\u30c3\u30c8\u5411\u3051\u306e\u30cf\u30a4\u30a8\u30f3\u30c9PCB\u88fd\u9020\u30fb\u7d44\u7acb\u306e\u30ef\u30f3\u30b9\u30c8\u30c3\u30d7\u30b5\u30d7\u30e9\u30a4\u30e4\u30fc\u3002.","publisher":{"@id":"https:\/\/www.sprintpcbgroup.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.sprintpcbgroup.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"ja"},{"@type":"Organization","@id":"https:\/\/www.sprintpcbgroup.com\/#organization","name":"SprintpcbGroup","url":"https:\/\/www.sprintpcbgroup.com\/","logo":{"@type":"ImageObject","inLanguage":"ja","@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/01\/sprintpcbgroup-pcb-manufacturer-site-icon.png","contentUrl":"https:\/\/www.sprintpcbgroup.com\/wp-content\/uploads\/2026\/01\/sprintpcbgroup-pcb-manufacturer-site-icon.png","width":500,"height":500,"caption":"SprintpcbGroup"},"image":{"@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/profile.php?id=61582505616626","https:\/\/x.com\/xipu386771","https:\/\/www.linkedin.com\/company\/33304071\/admin\/page-posts\/published\/","https:\/\/www.youtube.com\/@Sprint-PCB"]},{"@type":"Person","@id":"https:\/\/www.sprintpcbgroup.com\/#\/schema\/person\/dafc2c514153973c78bd4a61a060fed4","name":"sprintpcbgroup","image":{"@type":"ImageObject","inLanguage":"ja","@id":"https:\/\/secure.gravatar.com\/avatar\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/fdbddef1ebb9e597362f2411c721f1621acddc3f3c4fcab08845d7163e7544de?s=96&d=mm&r=g","caption":"sprintpcbgroup"},"sameAs":["https:\/\/www.sprintpcbgroup.com"]}]}},"_links":{"self":[{"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/posts\/12426","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/comments?post=12426"}],"version-history":[{"count":1,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/posts\/12426\/revisions"}],"predecessor-version":[{"id":12454,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/posts\/12426\/revisions\/12454"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/media\/12363"}],"wp:attachment":[{"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/media?parent=12426"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/categories?post=12426"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.sprintpcbgroup.com\/ja\/wp-json\/wp\/v2\/tags?post=12426"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}